How To Measure Windows For Cellular Shades

Measuring your windows, doors, or skylights for cellular shades is easy! Cheque out the tips below, and you'll observe how to measure just similar a professional person!

Inside Mount or Exterior Mount?

Shade Is Inside the Window/Door Frame

The most common method of mounting.
The brackets that hold the shade are screwed into the inside-top of the frame.
A minimum of 1″ of apartment surface is necessary for mounting the brackets (run into Flush vs. Shallow Mount, below).

Shade Is Outside the Window/Door Frame

Typically used when there is not enough frame depth for inside mount.
The brackets that hold the shade are screwed into the trim above the window frame or the wall higher up the trim.
A minimum of 1″ of flat surface is necessary for mounting the brackets.

Flush Within Mount or Shallow Inside Mount?

Flush vs. Shallow Mount

Affluent Inside Mountain means the entire shade fits within the window frame. In other words, if you were to run your hand along the wall or window frame, your hand would non bump into the shade. The minimum window frame depth required for a affluent mount is 2 1/4″.
Shallow Within Mountain means there'southward non plenty frame depth for a flush mount, so the front of the shade volition protrude into the room somewhat. This is non uncommon, and information technology does not affect the operation of the shade. A shallow mount can exist achieved with as petty as 1″ of frame depth.

What About Energy Efficient Side Tracks?

Tin can I Add Side Tracks?

Side tracks are an selection for all of our double-cell shades, with the exception of motorized shades.
Side tracks piece of work with inside-mount shades, but.
Side tracks crave a window frame depth of at to the lowest degree 1 1/4″.

Important Measuring Tips

How to Measure Like a Pro

Ever provide the width measurement first, then the elevation. A 24″ x 36″ shade is 24″ broad and 36″ loftier.
Measurements should exist rounded to the nearest one/eight″.
E'er measure the width in 3 placedue south – near the elevation of the window, near the heart of the window, and near the bottom of the window.
Always measure the height in iii places – almost the left side of the window, nearly the middle of the window, and virtually the right side of the window.
For shades that volition have side tracks and for skylight shades, you lot'll as well demand to measure the two diagonals – from the meridian-left corner to the bottom-right corner, and from the top-right corner to the bottom-left corner.

Measuring for Inside Mount

If Y'all Are Mounting Inside the Window Frame

Measure out the exact window opening – for example, from the inside-left of the window frame to the within-right, and from the inside-meridian to the bottom/sill.
- Practice not make any adjustments or have whatsoever deductions.
- Using your exact measurements and our expertise, we will build your shade to fit just right.
Measuring the width:
- Measure the width in three places – near the top of the window, well-nigh the middle of the window, and well-nigh the lesser of the window.
- For each measurement, circular down to the nearest 1/8″.
- Provide us with the smallest of the 3 measurements.
Measuring the acme:
- Measure the height in 3 places – most the left side of the window, near the eye of the window, and most the right side of the window.
- If you are adding side tracks, circular each measurement down to the nearest i/eight″ and provide us with the smallest of the 3 measurements.
- If you are Non calculation side tracks, round each measurement up to the nearest i/8″ and provide united states with the largest of the 3 measurements.
Measuring the diagonals (only necessary if ordering side tracks):
- Measure from the top-left corner of the window opening to the bottom-right corner. Then measure from the height-right corner to the lesser-left corner.
- If these ii measurements differ past more than 1/4″, side tracks will not work with the window unless the opening is shimmed or repaired.

Measuring for Outside Mount

If You lot Are Mounting Outside the Window Frame

Mensurate the exact area yous want to cover.
- Exercise not brand whatsoever adjustments or take any deductions.
- The width you give us volition be the verbal width that nosotros make your material. (Annotation: Due to the end caps on the headrail, it will be simply slightly wider than the fabric.)
- The acme you give us volition be the exact height of the shade, from the top of the headrail to the lesser of the bottom track.
Measuring the width:
- Mensurate the width in iii places – near the top of the window, nearly the middle of the window, and near the bottom of the window.
- For each measurement, round up to the nearest 1/8″.
- Provide u.s. with the largest of the 3 measurements.
Measuring the summit:
- Measure the tiptop in 3 places – nearly the left side of the window, near the middle of the window, and nigh the correct side of the window.
- For each measurement, round up to the nearest 1/8″.
- Provide u.s. with the largest of the iii measurements.

How to Measure for Outside Mount

Measuring for Skylight Shades

How to Measure out for Skylight Shades

Skylight shades take a few special requirements:
- Skylight shades require an inside flush mountain, with a apartment mounting surface of at least 2″.
- Skylight shades require that you take diagonal measurements. If the two diagonals are different by more than ane/4″, the opening is not sufficiently rectangular and your shade will non fit or operate correctly.
- If any ii of your width measurements are different by more than 3/eight″, then 1 or both sides of the opening will need to exist shimmed, and you will need to take new measurements.
Measure the skylight opening at the depth of the opening where you intend to install your shade.
- Practice not make any adjustments or take whatever deductions.
- Using your exact measurements and our expertise, we will build your shade to fit just right.
Measuring the width:
- Measure the width in 3 places – near the top of the opening, most the middle of the opening, and near the bottom of the opening.
- For each measurement, round down to the nearest one/8″.
- Provide us with the smallest of the 3 measurements.
Measuring the peak:
- Measure the height in iii places – near the left side of the opening, near the middle of the opening, and near the right side of the opening.
- For each measurement, round down to the nearest 1/eight″.
- Provide us with the smallest of the 3 measurements.
Measuring the diagonals:
- Measure from the top-left corner of the skylight opening to the bottom-right corner. Then mensurate from the summit-right corner to the bottom-left corner.
- If these two measurements differ by more than 1/4″, the opening will need to be shimmed or repaired.